eX-C1110 – Moduli Estensori Gigabit Ethernet

1 port RJ45 – 10/100/1000Base-T - Shielded

Auto-MDIX enables proper operation with either straight-through or crossover cabling

Distance up to 100 meters (328 feet) as per IEEE 802.3

1522 bytes

Ethernet Extenders must be connected in pairs using unconditioned wire. Circuits that run through signal equalization equipment are not permitted.

TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING. Choice of RJ45, BNC or terminal block models for VDSL link connector:

• RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)
• BNC – Coaxial 50 and 75 ohm cable with BNC connector
• Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling between 19 (0.9 mm) and 26 AWG (0.44 mm).

Actual distance and rates experienced will depend on condition and gauge of wire used. This Rate/Reach table applies to 24 AWG (0.5 MM) twisted pair wiring on RJ45 (RJ) and terminal block (TB) models

Module occupies a single slot in MCR1900 and MCR200 chassis

This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.

Ethernet Extender is operating in CO VDSL mode

Ethernet Extender is operating in CPE VDSL mode

Indicates Link Status and activity on the Interlink (VDSL) port

Indicates link status and activity on Ethernet port.

Two switches enable the user to select the right balance between speed and distance for their environment.

Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.

• Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex.
• Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.

• Standard (Default) – The 10/100/1000Base-T link remains active independent of the state of the Ethernet link on its remote peer.
• Link Pass-Through - the state of the 10/100/1000Base-T Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100/1000Base-T Ethernet link on its remote Ethernet Extender peer. This enables a managed switch to report the state of the remote device to its network management system.

• Enabled - A loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers
• Disabled (Default) – The state of the VDSL link is not propagated to the 10/100/1000Base-T port

• Enabled - The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its peer.
• Disabled (Default - Up)

When Auto-Negotiation switch is disabled, fixed speed can be set at 100 (Default) or 10

When Auto-Negotiation switch is disabled, Duplex can be set at Full (Default) or Half

0°C to 50°C (32°F to 122°F)

minimum range of -25°C to 70°C (-13°F to 158°F)

5% to 90% non-condensing

5% to 95% non-condensing

Up to 3,048 meters (10,000 feet)

14.3

4.2

446,387 Hours

Calculation model based on MIL-HDBK-217-FN2 @ 30°C

0.25 kg, 0.55 lbs

150 x 210 x 40 mm, 5.9 x 8.3 x 1.6 inches

• FCC Part 15 Class A, EN55022 Class A
• CISPR 32:2015/EN 55032:2015 (Class A)
• EN61000-3-2

CISPR 24:2010/EN 55024:2010

• UL/EN/IEC 62368-1
• CAN/CSA C22.2 No. 62368-1

• UL 60950-1
• IEC 60950-1(ed 2); am1, am2
• EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013

• CE

Reach, RoHS and WEEE Compliant

• ECCN: 5A991
• HTSUS Number: 8517.62.0020
• Perle Limited Lifetime Warranty