Estensori Fast Ethernet PoE eXP-S110

Remote (Power over Ethernet)

Local (power over link - VDSL)

eXP-1S110E

Local power adapter or VDSL

eXP-4S110E

Local power adapter or VDSL

• Local power adapter or
• PoE Power Sourcing Equipment such as a Cisco PoE+ Switch on port #1
• PoE+ power injector

• Local power adapter or
• PoE Power Sourcing Equipment such as a Cisco PoE+ Switch on port #1
• PoE+ power injector

eXP-1S110E

Ethernet

eXP-4S110E

Ethernet

eXP-1S110L

Link (VDSL Interlink)

eXP-4S110L

Link (VDSL Interlink)

Barrel or terminal block

eXP-1S110E

46V to 57

eXP-4S110E

46V to 57

eXP-1S110L

29 to 57

eXP-4S110L

29 to 57

eXP-1S110E

24 to 57

eXP-4S110E

24 to 57

eXP-1S110L

N/A

eXP-4S110L

N/A

48vDC, 60 watts is included when purchased an individual basis. One 48vDC 60 watts adapter is provided in each kit.

5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block

Remote (Power over Ethernet)

Local (power over link - VDSL)

eXP-1S110E

1 port RJ45 Shielded

eXP-4S110E

4 port RJ45 Shielded

eXP-1S110L

1 port RJ45 Shielded

eXP-4S110L

4 port RJ45 Shielded

Auto-MDIX enables proper operation with either straight-through or crossover cabling

Distance up to 100 meters (328 feet) as per IEEE 802.3

1522

eXP-1S110E

PSE (PoE) IEEE 802.3af

eXP-4S110E

PSE (PoE) IEEE 802.3af

eXP-1S110L

PD (Class 0 or 4 device)

eXP-4S110L

PD (Class 0 or 4 device)

eXP-1S110E

Refer to the Power Reach Installation Planning Guide

eXP-4S110E

Refer to the Power Reach Installation Planning Guide

eXP-1S110L

N/A

eXP-4S110L

N/A

• Alternative A (default) on all ports
  Pins 3,6 Neg, Pins 1,2 Pos
• Alternative B: selectable on port #1
  Pins 7,8 Neg, Pins 4,5 Pos
• Legacy Cisco Pre-Standard: selectable on port #1
  Pins 7,8 Pos, Pins 4,5 Neg

• Alternative A (default) on all ports
  Pins 3,6 Neg, Pins 1,2 Pos
• Alternative B: selectable on port #1
  Pins 7,8 Neg, Pins 4,5 Pos
• Legacy Cisco Pre-Standard: selectable on port #1
  Pins 7,8 Pos, Pins 4,5 Neg

eXP-1S110L

N/A

eXP-4S110L

N/A

Ethernet Extenders must be connected in pairs using unconditioned wire. Circuits that run through signal equalization equipment are not permitted.

TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING. Choice of RJ45, BNC or terminal block models for VDSL link connector:

• RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)
• BNC – Coaxial 50 and 75 ohm cable with BNC connector
• Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling between 19 (0.9 mm) and 26 AWG (0.44 mm).

eXP-1S110E

N/A

eXP-4S110E

N/A

eXP-1S110L

Injects SELV compliant voltage and VDSL data across a single pair of cooper wires (pins 4 and 5) or 2 conductor BNC coaxial cable

eXP-4S110L

Injects SELV compliant voltage and VDSL data across a single pair of cooper wires (pins 4 and 5) or 2 conductor BNC coaxial cable

eXP-1S110E

N/A

eXP-4S110E

N/A

eXP-1S110L

Short Circuit protection provided

eXP-4S110L

Short Circuit protection provided

eXP-1S110E

The voltage from the VDSL link requires proper polarity in order to provide power to the remote extender. Reverse polarity protection however will ensure that there is no damage to the extender

eXP-4S110E

The voltage from the VDSL link requires proper polarity in order to provide power to the remote extender. Reverse polarity protection however will ensure that there is no damage to the extender

eXP-1S110L

N/A

eXP-4S110L

N/A

When used with 4-pair cable such as CAT5 on the VDSL Interlink port, an optional internal strap selection on the Ethernet Extender will provide VDSL transmission data on 1 pair and power across the 3 other pairs enabling even greater distances for power transmission to be achieved

Actual distance and rates experienced will depend on condition and gauge of wire used. This Rate/Reach table applies to 24 AWG (0.5 MM) twisted pair wiring on RJ45 (RJ) and terminal block (TB) models

This table applies when the power multiplier option is selected

The amount of available power at the PoE PD is dependent on the scenario planned.
Refer to the Power Reach Installation Planning Guide

Remote (Power over Ethernet)

Local (power over link - VDSL)

This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.

Ethernet Extender is operating in CO VDSL mode

Ethernet Extender is operating in CPE VDSL mode

Indicates Link Status and activity on the Interlink (VDSL) port

Indicates link status and activity on Ethernet port(s).

This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE;

GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied)

YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is :

• Not connected
• Has not detected a compliant PD and is not applying power
• PSE has turned off power for Reset function

OFF — PSE function switch disabled

RED — Blinking: Error Conditions

• Capacitance too High — 1 blink
• Resistance too Low or short circuit — 2 blinks
• Resistance too high or open circuit — 3 blinks

Switch settings are accessible through a side opening in the chassis

Two switches enable the user to select the right balance between speed and distance for their environment.

Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.

• Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100Base-TX interface. It is set to advertise full duplex.
• Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.

When Auto-Negotiation switch is disabled, a fixed speed can be forced on port 1 to 100 (Default) or 10

When Auto-Negotiation switch is disabled, Full or half Duplex can be forced on port 1 to Full (Default) or Half

• Standard (Default) - The 10/100Base-TX link remains active independent of the state of the Ethernet link on its remote peer.
• Link Pass-Through - state of the 10/100Base-TX Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100Base-TX Ethernet link on its remote Ethernet Extender peer.

• Enabled – A loss of VDSL link will drop the 10/100 Ethernet port on each end until the link recovers
• Disabled (Default) - The state of the VDSL link is not propagated to the 10/100Base-TX port

• Enabled – The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its remote peer.
• Disabled (Default - Up)

Remote (Power over Ethernet)

Local (power over link - VDSL)

eXP-1S110E

N/A

eXP-4S110E

N/A

eXP-1S110L

(Internal strap) for PoE PD classification type identification for attached IEEE 802.3at compliant PoE+ switch on port #1

Class 0 – PoE PD device - 0.44-12.94W (Default)

Class 4 – PoE+ PD device 12.95 – 25.5W

eXP-4S110L

(Internal strap) for PoE PD classification type identification for attached IEEE 802.3at compliant PoE+ switch on port #1

Class 0 – PoE PD device - 0.44-12.94W (Default)

Class 4 – PoE+ PD device 12.95 – 25.5W

eXP-1S110E

When enabled (down), the Ethernet Extender will upon loss of link on the VDSL Interlink port, turn off PSE output power to the PD device for 2 seconds then turn the power back on. The power remains on until the VDSL link transitions from up to down again.

When PD Power Reset is disabled (default), loss of VDSL link has no effect on power supplied to the PD.

eXP-4S110E

When enabled (down), the Ethernet Extender will upon loss of link on the VDSL Interlink port, turn off PSE output power to the PD device for 2 seconds then turn the power back on. The power remains on until the VDSL link transitions from up to down again.

When PD Power Reset is disabled (default), loss of VDSL link has no effect on power supplied to the PD.

eXP-1S110L

N/A

eXP-4S110L

N/A

0°C to 50°C (-32°F to 122°F)

minimum range of -25°C to 70°C (-13°F to 158°F)

5% to 90% non-condensing

5% to 95% non-condensing

Up to 3,048 meters (10,000 feet)

Remote (Power over Ethernet)

Local (power over link - VDSL)

eXP-1S110E

108 @ 48vdc

eXP-4S110E

121 @ 48vdc

eXP-1S110L

129 @ 48vdc

eXP-4S110L

142 @ 48vdc

eXP-1S110E

5.2

eXP-4S110E

5.8

eXP-4S110L

6.2

eXP-1S110L

6.8

eXP-1S110E

17.74

eXP-4S110E

19.79

eXP-1S110L

21.16

eXP-4S110L

23.20

eXP-1S110E

185,061 Hours

eXP-4S110E

169,935 Hours

eXP-1S110L

199,390 Hours

eXP-4S110L

182,735 Hours

eXP-1S110E

300,472 Hours

eXP-4S110E

262,530 Hours

eXP-1S110L

340,165 Hours

eXP-4S110L

294,389 Hours

Calculation model based on MIL-HDBK-217-FN2 @ 30°C

Standard

Optional

Optional

Remote (Power over Ethernet)

Local (power over link - VDSL)

eXP-1S110E

0.58 Kg, 1.3 lbs

eXP-4S110E

0.61Kg, 1.34 lbs

eXP-1S110L

0.58 Kg, 1.3 lbs

eXP-1S110L

0.61Kg, 1.34 lbs

163 x 116 x 37 mm, 6.4 x 4.6 x 1.46 inches

Remote (Power over Ethernet)

Local (power over link - VDSL)

eXP-1S110E

1.27 Kg, 2.8 lbs

eXP-4S110E

1.3 Kg, 2.86 lbs

eXP-1S110L

1.27 Kg, 2.8 lbs

eXP-1S110L

1.3 Kg, 2.86 lbs

20 x 30 x 7 cm, 7.9 x 11.8 x 2.8 inches

• CISPR 32:2015/EN 55032:2015 (Class A)
• IEC/EN 61000-3-2
• IEC/EN 61000-3-3

• CISPR 24:2010/EN 55024:2010
• IEC/EN 61000-4-2
• IEC/EN 61000-4-3
• IEC/EN 61000-4-4
• IEC/EN 61000-4-5
• IEC/EN 61000-4-6
• IEC/EN 61000-4-8
• IEC/EN 61000-4-11

• UL/EN/IEC 62368-1
• CAN/CSA C22.2 No. 62368-1

• UL 60950-1
• IEC 60950-1(ed 2); am1, am2
• EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013

• CE

Reach, RoHS and WEEE Compliant

• ECCN: 5A991
• HTSUS Number: 8517.62.0020
• Perle Limited Lifetime Warranty